Speck-electronics LiLo Bedienungsanleitung PDF herunterladen

LiLo - Mixer Stand Assembly Instructions

Information and specifications are subject to change without notice.

Speck Electronics • 341 E. Alvarado Street, Fallbrook, California 92028, USA

Voice: +760-723-4281 • Fax: +760-723-3294 • email: [email protected] • www.speck.com

[C] Cross brace

[D] Top tray

[B] Right upright support

[A] Left upright support

[G] 8-32 x 3/8” Pan Head Phillips

[E] 1/4”-28 x 1.5” Button head socket bolt

[F] Allen Key Wrench

Front

Rear

1. Install the button head socket bolt [E] through the upper hole of either the left or right support [A] or [B].

Note that the inside of the supports have (3) threaded holes at the top.

Screw this bolt into the upper threaded hole at either end of the cross brace [C]. Note that the bottom of the

cross brace has a cosmetic difference from the top. Hand tighten this bolt only.

2. Repeat this procedure for the other side of the support [A] or [B]. Hand tighten this bolt only.

3. Install the remaining (2) s [E] on each side. Hand tighten these bolts only.

4. Place the top tray [D] upside down on a clean flat surface. Place the partially assembled supports with

cross brace so the (3) threaded holes on each support are aligned with the (3) through-holes of the top tray

[D]. Install (6) Phillips screws [G], (three on each side) through these holes and tighten with a Phillips

screwdriver.

5. Once the top tray [D] has been attached to the supports and the Phillips screws [G] have been tightened,

use the supplied Allen key wrench [F] to tighten the (4) [E].

6. This completes the assembly the stand. Place the assembled stand upright on the floor.

button head socket bolt

button head socket bolts

[E] 2 per side

[G] 3 per side

Now the LiLo mixer will be placed on the stand.

~Important~

Before placing the LiLo mixer on the stand, it is very

important that the stand is in the correct position to

receive the mixer. The front of the LiLo mixer must

be place over the long section of the stands base as

shown in [J].

7. Place the LiLo mixer on the stand so the center area

of the LiLo's side panels is positioned at the middle of

the upright support as shown in [H].

The rubber bumpers on the top surface of the stand

will prevent the LiLo mixer from sliding forward or

backward, so it will be necessary to lift the mixer away

from the stands' top tray in order to make fine

adjustments to the final position.

8. The final position of the mixer on the stand should

be set so the rear edge of the LiLo's side panels are

9.25” [235mm] from the rear edge of the support as

shown in [ I ].

9.25”

235mm

[ I ]

[J] Front of stand

[H]

Inhaltsverzeichnis

Seite 1

Weitere Dokumente für Audio Speck-electronics LiLo

Um das Dokument anzuzeigen Speck-electronics LiLo Bedienungsanleitung

Speck-electronics LiLo Bedienungsanleitung (38 Seiten)

Kommentare zu diesen Handbüchern

Keine Kommentare

Speck-electronics LiLo Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Audio Speck-electronics LiLo herunter. Speck Electronics LiLo User Manual Benutzerhandbuch

Inhaltsverzeichnis

Weitere Dokumente für Audio Speck-electronics LiLo

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Audio Speck-electronics LiLo